Replies to This Discussion

Permalink Reply by Kaung Lay on January 28, 2012 at 12:44am

DHCP Sever ko configure lote htar tar kaw ta kal mhan pi lar?

Ta kal lote configure lote htar tal mhar tal so yin lal IP ma kya naing par buu.........

Not Pyee....... Wireless Access Point (WAP) mhar kaw DHCP Service ko Disable lote htar phoe lo at par tal..( ae dar ko lal sit say think par tal)

ta kal loe Wireless Access Point mhar par tae DHCP Service ko use mal so yin tot Windows Server 2003 mhar DHCP Server ko install  lote htar sa yar ma lo par buu.........

but..... ta kal lo Windows Server 2003 mhar pal DHCP Service ko install lote mal so yin tot....out mhar Step By Step Guide pay lite par tal..........

First Step -----

                          Start > Program > Control Panel > Add/Remove Program > Add/Remove Windows Components > Networking Service > (On) Dynamic Host Configuration Check box > Click Ok > Ok > Click Next ........ DHCP Service intsall finish!!!!

Second Step ----

                          Open Command Line (Run box ----  cmd )

C:\Documents and Settings\Administrator>netsh

netsh>dhcp

netsh dhcp>server

netsh dhcp server>add scope (Your Network IP Address) (SubnetMask) (ScopeName)

netsh dhcp server>add scope 192.168.10.0 255.255.255.0 MyDHCPScope

netsh dhcp server>scope 192.168.10.0

netsh dhcp server scope>add iprange (Your Start IP Address) (Your End IP Address)

netsh dhcp server scope>add iprange 192.168.10.2 192.168.10.254

netsh dhcp server scope>set optinsvalue 003 IPADDRESS (Your Default Gateway or Router IPAddress)

netsh dhcp server scope>set optionvalue 003 IPADDRESS 192.168.10.1

netsh dhcp server scope>set optinsvalue 006 IPADDRESS (PreferredDNSServer) (SecondaryDNSServer)

netsh dhcp server scope>set optionvalue 006 IPADDRESS 203.81.162.22 203.81.162.23

netsh dhcp server scope>exit

__________-_____________Finish DHCP Service Configuration________________________________

Note: ku DHCP ko configure lote htar tae nay yar mhar DHCP Server IP ko (192.168.10.1) pay htar tar phit par tal

not pyee

netsh dhcp server scope>set optionvalue 003 and 006 ko lo at mae htet pay ya mhar phit par tal ... ma lo at buu so yin tot ae di command 2 line ko type lote sa yar ma lo par buu.........

ae ... tha ti pay chin tar lay shi tay tal.... ta kal loe Windows Server 2003 paw mhar AD tin thar tal so yin tot...... Start> Administrative Tools> DHCP ko open pyee DHCP Server Node ko (Right Click) ---> Authorize --> ko Click lote pay ya par mal..........

a sin pyay par say lo su tong pay par tal...... ta kal loe ta sone ta yar a khat a khal shi kae tal so yin tot

73109675 ko phone sat pyee tot may lo ya par tal..... My Phone No. par......

I hope...... a sin pyay par say loe su tong pay par tal........

• ▶ Reply

Permalink Reply by johnthss on January 28, 2012 at 4:54pm

thank your post

• ▶ Reply

Permalink Reply by firebird on January 28, 2012 at 7:39pm

a khu lo shin pya pay tar kyay zu tin par tal.sait dat ko lay sar tal

• ▶ Reply

Permalink Reply by GaaRa on January 29, 2012 at 3:43pm

Thz for helping me.

• ▶ Reply

Permalink Reply by Kaung Lay on January 29, 2012 at 4:11pm

Barcamp 2012 ko kyo so par tal!!!!!!!!

Barcamp mhar my topic pyu lote mhar phit par tal!

First Day mhar ---------> Building Linux Openmeeting Server , Hacking Wireless (WEP , WPA2 ) , Hacking       Wireless Hotspot Server Database

Second Day Mhar ----------> Hacking Cisco Router and Windows Server 2003

 ae dar twe ko pyu lote pyay pay twar mhar phit par tal............

arr lone lar yout pyee topic ko arr pay mal lo myaw link par tal........

Topic pyu lote mae Room ka a ti a kyay ma ti ya tay par buu...... dar kyunt ......... Barcamp Day kyay yin...

Phone No.. 0973109675 ko connect lote pyee Room No. ko may myan naing par tal........

arr lone ko kyo so par tal.........

IT enviorment road paw mhar a tu tu twar nay kya tae nyi a ko twe arr lone ko kyay zuu tin par tal!!!!!

• ▶ Reply